Plumbing Basics: An Essential for Installing a Bathtub
Click HereThe writer is making a few good observations on Tools You Need to Install a New Bathtub overall in this post further down.
Mounting a bathtub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a reasonably difficult task. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open a wall to get rid of the old bathtub and place the new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the task as well as fit attempting it. As opposed to employing a service provider to take control of a halfway-completed task, it is better to consider using one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new tub in your shower room if you have currently gotten a new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your tools as well as product checklist must make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous kind should be connected to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Using the two wood boards under its feet, put the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub until the level checks out degree.
To set up faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water and check all joints and new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as also check the overflow electrical outlet and the normal outlet for leakages.
Finally, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub ought to wait until the tub has actually been made use of at the very least once as this will certainly settle it right into its last position.
Planning for the Installation
Firstly, the sustaining structure provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to avoid strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a rigid seal, triggering the water to permeate the wall surface between the bath and the tiling, causing problems with moisture and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealer can fracture relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that post about How to Install a Bathtub when browsing the internet. For those who enjoyed our blog posting kindly make sure you remember to share it. I cherish reading our article about Installing A Bathtub.
We've got answers!